SimXPro XT160 Heavy Triple Monitor Stand Setup Guide

By SimXPro l Sim Racing Shop | Published: 2026-10-31

Category: How-to Guides

Learn how to assemble and align the SimXPro XT160 with the Heavy Triple Monitor Stand. Step-by-step instructions, common mistakes, and practical tips for a rigid triple-screen rig.

Quick Answer

For a rigid triple-monitor sim rig, pair the SimXPro XT160 cockpit with the Heavy Triple Screen Setup and follow a sequence that aligns the monitors before final tightening. This guide walks you through the key steps and the mistakes to avoid.

Why the Heavy Triple Screen Setup matters

The SimXPro Heavy Triple Screen Setup is a freestanding 4040-profile monitor mount that supports VESA 75/100/200 patterns, so it can handle large and heavy displays. Because it's freestanding, it doesn't rely on the cockpit for stability, which reduces vibration transfer and makes the rig easier to adjust independently.

The main trade-off is that a freestanding stand takes up floor space and requires careful alignment with the cockpit. You'll need to position the stand so the center monitor sits at the correct distance and height relative to your seat, which is easier to do before you tighten everything down.

Planning the layout before you start

Before assembling, decide on the monitor size, the intended viewing distance, and the angle of the side screens. The Heavy Triple Screen Setup allows independent adjustment of each monitor, but the stand's footprint and the cockpit's position will determine the practical range.

Measure your space to ensure the freestanding stand fits alongside the XT160. Remember that the stand is separate, so you'll need clearance on both sides for the side monitors to swing out at your desired angle.

Step-by-Step Setup Process

Assemble the Heavy Triple Screen Stand: Start by assembling the freestanding stand according to the included instructions. Lay out all 4040 profiles and hardware, and loosely tighten the joints that will hold the monitor brackets. Do not fully tighten yet—you'll need some play for alignment later. Common mistake: tightening everything at this stage makes later adjustments difficult. Keep joints snug but movable.
Position the stand relative to the cockpit: Place the assembled stand in front of your SimXPro XT120 cockpit, aligning the center of the stand with the center of the wheel base. Adjust the height of the stand's uprights so the center monitor will sit at your eye level when seated. Checkpoint: use a tape measure to center the stand exactly; even a small offset will misalign the side screens.
Mount the center monitor: Attach the center monitor to the VESA bracket using the correct screw size for your monitor (75, 100, or 200mm pattern). Tighten the screws firmly but avoid over-tightening. Slide the bracket up or down to set the desired height, then lock it in place. Common mistake: using the wrong VESA pattern or screw length can damage the monitor. Verify the pattern before mounting.
Mount the side monitors and set the angle: Attach the left and right monitors to their respective VESA brackets. Pivot the side arms to your preferred angle (typically 15–30 degrees for immersion). Ensure the side monitors are at the same height and distance from your eyes as the center monitor. Checkpoint: use a string or laser level to confirm all three monitors are at the same height and aligned horizontally.
Tighten all joints and finalize: Once the monitors are positioned correctly, tighten all bolts on the stand, including the base, uprights, and monitor brackets. Double-check that the stand is stable and doesn't wobble when you lean on it. Finally, adjust the cockpit's seat and wheel to your preferred driving position. Common mistake: skipping the final tightening check; a loose joint can cause the monitors to sag or shift during use.

Product Facts

SimXPro XT120 + Heavy Triple Monitor Stand Bundle: This bundle pairs the SimXPro XT120 cockpit with the SimXPro HEAVY Triple Screen Setup, and each component can be viewed individually. You can buy the cockpit and monitor stand together for convenience, but you can also purchase them separately if you already own one part.
SimXPro XT120 + Heavy Triple Monitor Stand Bundle
SimXPro XT120 + Heavy Triple Monitor Stand Bundle: The Heavy Triple Screen Setup supports VESA 75/100/200 mounting patterns. This covers a wide range of monitors, including larger displays that need the 200mm pattern for a secure fit.