Sim Floor Mat and Rig Care: Protect Cockpit and Floor
By SimXPro l Sim Racing Shop | Published: 2026-10-16
Category: Tips en onderhoud
A practical, ordered routine for using a sim racing floor mat and caring for your cockpit so your floor stays protected and your rig stays stable.
Quick answer
Put a sim racing floor mat under the cockpit first, then build a short monthly care routine: check frame fasteners, clean the mat and floor, and inspect contact points. The SimXPro Sim Floor Mat is sized 950 × 1500 mm to give most SimXPro cockpits a clean, stable foundation while absorbing vibration and reducing noise.
Why the floor under your rig matters
A hard floor and a stiff aluminium cockpit transmit every braking and steering input straight into the room. Over time, that movement can scuff flooring, walk the rig out of position, and add noise that makes long sessions less pleasant. A mat is not just cosmetic: it gives the frame a defined footprint, reduces the chance of the rig shifting during heavy load-cell braking, and makes it easier to see when something has moved.
What to check before you place the mat
Measure the floor area your cockpit actually occupies, including pedal plate and any rear extension. The SimXPro Sim Floor Mat measures 950 × 1500 mm, so compare that against your frame footprint before ordering. If your rig is longer than the mat, decide whether you want the mat centered under the seat and wheel deck or under the pedals where movement is strongest. Also check that the floor is clean and dry; grit trapped under a mat will wear both the mat and the floor finish.
Cleaning products that are safe for mats and frames
Use a mild soap and water solution for the mat, then let it dry fully before putting the rig back. Avoid solvent-heavy cleaners on printed or coated surfaces because they can dull the finish. For aluminium profile, a damp cloth is usually enough; dry the profile afterward so water does not sit in the grooves. If you use a vacuum on the mat, use a brush attachment rather than a beater bar, which can catch the edge.
Your step-by-step floor mat and rig care routine
- 1. Clear and inspect the floor area: Remove the cockpit or slide it aside, then sweep and wipe the floor. Look for grit, small screws, or cable ties that could press into the mat. Check the floor for existing scuffs so you can tell later whether the rig is moving. Checkpoint: the floor should be dry and free of debris before the mat goes down.
- 2. Position the mat under the cockpit footprint: Lay the SimXPro Sim Floor Mat so the main load points—seat, wheel deck, and pedal plate—sit on the mat. If your frame is longer than 1500 mm, decide which end needs protection most; pedals and the seat are usually the priority. Mark the mat edge with tape if you want a repeatable position. Common mistake: centering the mat on the frame instead of on the load points, which leaves the pedals half off the mat.
- 3. Set the rig down and check for rocking: Lower the cockpit onto the mat and press down on each corner. A mat with a slight give can hide an uneven floor, so check that all feet contact the mat evenly. If one corner floats, add a thin shim under that foot rather than forcing the frame. Checkpoint: no corner should lift or rock when you push down firmly.
- 4. Re-torque fasteners after the first sessions: New setups settle. After the first few hours of driving, check the main frame bolts, seat brackets, and wheel deck fasteners. Vibration plus a soft mat can let a bolt back out slightly, so tighten to the manufacturer's spec and recheck monthly. Common mistake: assuming the rig is still tight because it felt fine on day one.
- 5. Clean the mat and floor monthly: Vacuum the mat with a brush attachment, then wipe with mild soap and water. Dry it fully before use. While the mat is up, clean the floor underneath and inspect for new scuffs or movement marks. Checkpoint: if you see fresh scuff marks, the rig is shifting—reposition or add grip.
- 6. Inspect contact points and cables: Look at where the frame meets the mat, where pedals mount, and where cables run. A mat can trap heat or pinch a cable if routed underneath. Keep cables above the mat or in a channel so they are not crushed by the frame. Common mistake: running power or USB cables under the mat where they get pinched and fail.
- 7. Refresh or replace when wear shows: If the mat is compressed flat, torn at the edges, or no longer staying put, it is time to replace it. A worn mat loses its vibration and anti-slip benefits, and a curled edge becomes a trip hazard. Note the date you installed it so you can judge wear fairly. Checkpoint: replace when the mat no longer sits flat or the rig moves during braking.
Product facts
- SimXPro Sim Floor Mat: SimXPro Sim Floor Mat measures 950 × 1500 mm and is designed to absorb vibrations, reduce noise transmitted through the floor, and prevent the rig from shifting during demanding braking and steering inputs. A defined, slightly cushioned footprint keeps the cockpit from walking and cuts down on noise, which matters most if you run a load-cell brake or share the room with others.
- SimXPro Sim Floor Mat: The mat provides a clean foundation for every SimXPro cockpit and is available in multiple design options. Because it is sized for SimXPro cockpits, you can order it with confidence for a standard frame and choose a design that matches your room instead of hiding the rig.
