How to Mount a Sim Racing Monitor on a Rig
By SimXPro l Sim Racing Shop | Published: 2026-10-17
Category: How-to Guides
Learn how to mount a sim racing monitor directly to your cockpit. Step-by-step guide covering VESA brackets, integrated mounts, and triple screen setups.
Quick answer
Mount your sim racing monitor directly to the cockpit using an integrated monitor mount. This eliminates the need for a separate floor stand and keeps the screen centered above the steering wheel. Choose a VESA-compatible mount that matches your display size and weight, then bolt it to your rig's profile channels.
Why an integrated mount beats a floor stand
An integrated monitor mount attaches directly to your sim racing cockpit, not the floor. This saves floor space and makes the entire rig a single, moveable unit. The monitor stays centered above the wheel deck, which improves your seating position and field of view. A separate floor stand can shift or require careful alignment every time you move the rig.
VESA compatibility and display weight
Most sim racing monitor mounts use the VESA 75x75 or 100x100 standard. Check the back of your monitor for the screw pattern. The mount must also support your monitor's weight. A single ultrawide display typically needs a heavier-duty bracket than a standard 24-inch screen. If your monitor has an unusual VESA pattern, you may need an adapter plate.
Triple monitor considerations
For a triple screen setup, an integrated triple monitor mount positions all three displays above the wheel deck without a separate stand. This creates a wraparound field of view and keeps the screens at a consistent height and angle. Make sure your cockpit has enough profile length to support the mount's width. Triple mounts are heavier, so check the total weight capacity.
Step-by-step mounting process
- 1. Prepare the cockpit and mount: Clear the area around your rig. Remove any existing brackets or accessories from the front profile channels. Lay out the integrated mount parts and confirm you have all bolts, T-nuts, and tools. Common mistake: skipping the layout check and discovering a missing part mid-install. Checkpoint: verify all hardware matches the mount's manual before you start.
- 2. Attach the VESA plate to the monitor: Lay the monitor face-down on a soft, clean surface. Screw the VESA plate onto the back using the correct screws for your monitor's thread size. Do not overtighten. Common mistake: using screws that are too long, which can damage the display internals. Checkpoint: the plate should sit flush; if it wobbles, the screws are wrong.
- 3. Mount the bracket to the cockpit: Slide T-nuts into the front profile channels of your rig at the desired height. Bolt the integrated mount bracket onto the profiles. Tighten just enough to hold the bracket in place but leave room for final adjustment. Common mistake: tightening fully now, making height changes harder later. Checkpoint: the bracket should slide up and down with light force.
- 4. Attach the monitor to the bracket: With help, lift the monitor and hook the VESA plate onto the bracket's locking mechanism. Secure it with the provided screws or quick-release pins. Common mistake: trying to lift a large monitor alone, risking a drop or back strain. Checkpoint: the monitor clicks or locks into place before you let go.
- 5. Adjust height, tilt, and distance: Loosen the bracket's adjustment knobs. Set the monitor height so your eye level is roughly at the top third of the screen. Tilt the screen slightly toward you. Slide the mount forward or back to your preferred eye-to-screen distance. Tighten all knobs. Common mistake: setting the monitor too high, causing neck strain during long sessions. Checkpoint: sit in your driving position and confirm the screen is at natural eye level.
- 6. Cable management and final check: Route the display cable and power cord along the cockpit frame using cable clips or zip ties. Keep cables away from moving parts like the wheel base or pedal sliders. Common mistake: leaving cables loose, which can snag or create visual clutter. Checkpoint: all cables have slack for adjustment and are secured at least every 12 inches.
Monitor mounts that simplify the job
- SimXPro Single integrated monitor mount 75/100 VESA: SimXPro Single Integrated Monitor Mount - VESA 75/100. Premium aluminium profiles mount directly to the cockpit, keeping the monitor centred above the steering wheel. This mount is ideal for a single ultrawide or conventional display. It eliminates a floor stand and keeps your rig compact and easy to move.
- SimXPro GT - RS Triple monitor mount: SimXPro GT-RS Triple Monitor Mount positions three monitors directly above the wheel deck for a wraparound view. Made from powder-coated aluminium and reinforced steel. If you want a triple screen setup without a separate floor stand, this mount integrates cleanly with the GT-RS cockpit and gives you a wide, consistent field of view.
